Browsing by Author "Andres, Carl J., 1942-"
Now showing 1 - 6 of 6
Results Per Page
Sort Options
Item Color stability of light-activated bleach shade composites(2010) Al-Yakoubi, Yaser; Levon, John A.; Platt, Jeffrey A., 1958-; Kim, Seok-jin, 1967-; Brown, David T.; Andres, Carl J., 1942-This study evaluated the color stability of bleach shade composites when activated by a high-intensity quartz tungsten-halogen (QTH) light source after 1 day, 7 days, and 30 days of exposure to different conditions. The color stability of bleach shade composites depends on various factors, namely, the resin material, the shade of the resin material, the storage method, and the storage time.Item The effect of a novel photoinitiator system (RAP) on dental resin composites' flexural strength, polymerization stress, and degree of conversion(2009) Schaub, Kellie; Platt, Jeffrey A., 1958-; Andres, Carl J., 1942-; Levon, John A.; Brown, David; Hovijitra, Suteena, 1944-Objectives: A new technology has been introduced into the field of dental resin composites that professes to enhance light-curing efficiency. Rapid amplified photopolymerization (RAP) initiator technology has not yet been fully compared with resin composites with conventional initiators such as camphorquinone (CQ). The purpose of this study was to compare and contrast the effects of this novel technology (RAP) on properties of two light-cured resin composites. Flowable (EFQ) and microfilled (ESQ) experimental composites were fabricated and supplied from Tokuyama Dental with (w/RAP) and without RAP (w/o RAP). The flexural strength (MPa) and flexural modulus (MPa) were obtained using a three-point bending apparatus (Sintech Renew 1123, Instron Engineering Corp., Canton, MA). Polymerization stress curves were created using a tensometer (American Dental Association Health Foundation, NIST, Gaithersburg, MD) which were then used to calculate the maximum stress rate. Finally, the degree of conversion was measured using infrared spectroscopy (Jassco FT-IR spectrometer, Model: 4100, Jasco Corporation, Tokyo, Japan). When evaluating the flexural strength, the peak stress for EFQ w/RAP was significantly higher than EFQ w/o RAP (p = 0.0001). This was statistically not significant for the ESQ group, even though ESQ w/RAP did have a higher peak stress then ESQ w/o RAP (p = 0.28). The interaction between resin type and RAP was not significant when evaluating the flexural modulus (p = 0.21). Formulations with RAP had a significantly higher flexural modulus then w/o RAP (p = 0.0001). Experimental resins with RAP had significantly higher maximum stress rates than those w/o RAP when evaluating polymerization stress (p = 0.0001). Finally, groups w/ RAP appeared to have a higher degree of conversion than groups without (p = 0.0057). This study showed that the experimental composites with RAP had greater mechanical properties than those without. Unfortunately, the increase in polymerization stress causes concern clinically due to the chance of leakage at the restoration/tooth interface. One of the main potential disadvantages of this new RAP technology is an increase in the polymerization stress. Deciding if this amount of polymerization stress is clinically acceptable is yet to be accomplished.Item Evaluation of fracture resistance of three post and core systems in endodontically treated teeth under loading to failure; and marginal gap measurement before and after cyclic loading(2009) Saad, Amir N., 1979-; Platt, Jeffrey A., 1958-; Matis, Bruce A.; Andres, Carl J., 1942-; Katona, Thomas R.; Levon, John A.The purpose of this study was to evaluate the fracture resistance of three post and core systems in endodontically treated teeth by loading to failure, and to measure marginal gaps before and after cyclic loading. Sixty extracted canines were assigned to three groups. The groups tested were: 1) Single cast post and core (Group CP). 2) Prefabricated metal post and composite resin core (Group MR). 3) Glass fiber post and composite resin core (Group FR). All teeth were obturated and prepared to receive a post and core with a coping. Thirty teeth (10 from each group) were loaded to failure, and the other 30 teeth were fatigue-loaded. The marginal gaps on the facial and lingual surface of the fatigue-loaded group were measured before and after cyclic loading. There were two hypotheses for this study. The first was that the FR group would have less marginal gap opening on the lingual surface than the other groups. The second was that the CP group would have a higher load at failure than the other groups. Group CP was found to have a significantly smaller pre-loading marginal gap than group FR (p = 0.0265) and group MR (p = 0.0273), while groups FR and MR did not have a significantly different pre-loading marginal gaps (p = 0.86). Group FR had significantly less change in marginal gap than group MR (p = 0.0013). Groups CP and MR did not have significantly different changes in marginal gap (p = 0.09). Groups CP and FR did not have significantly different changes in marginal gap (p = 0.11). The three post types did not have significantly different maximum loads to failure (p= 0.49), moments of inertia at cervical area (p = 0.75), or moments of inertia at fracture site (p=0.12). There was no significant difference between groups CP, FR, and MR in the load-to-failure test. Group CP demonstrated the highest load-to-failure values; however, the highest load-to-failure mean was for group MR. All fractures observed in this study were catastrophic. Group FR demonstrated better stress distribution and caused no early fractures in the fatigue-loading group. All groups demonstrated significant marginal gap changes on the lingual surface after fatigue loading; however, group FR demonstrated <45 μm marginal gap opening. In group FR, the reduced marginal gap opening was attributed to the use of Panavia 21 with the proper surface treatments to bond to the tooth structure, the resin composite, and the metal coping.Item Mechanical properties evaluation of denture base PMMA enhanced with single- walled carbon nanotubes(2010) Scotti, Kevin; Chu, Tien-Min Gabriel; Paez de Mendoza, Carmen Y.; Andres, Carl J., 1942-; Levon, John A.; Hovijitra, Suteena, 1944-Recent theoretical and experimental studies, suggest that Carbon nanotubes are 10-100 times higher than the strongest steel at a fraction of the weight. There are two main types of CNTs that can have high structural perfection. Single-walled nanotubes (SWNTs) consist of a single graphite sheet seamlessly wrapped into a cylindrical tube. Multi-walled carbon nanotubes (MWNTs) comprise an array of such nanotubes concentrically nested like rings of a tree trunk. Denture base acrylics have been reinforced with different materials with limited success. No single reinforced material has showed a great statistical difference in mechanical improvement. The goal of this investigation was to study the effects of Single Walled Carbon Nanotubes reinforcement on the mechanical properties of commercially available denture base PMMA. Denture Base material was reinforced with Single-walled Carbon Nanotubes (SWNTs) at dispersion of 0.25 wt % (group 1), 0.50 wt % (group 2), 0.75 wt % (group 3) and 0.0 wt % (group 4, control). Samples from each group were evaluated for microhardness, flexural strength, flexural modulus, and fracture toughness. The samples were tested in two conditions, as manufactured (dry) and after storing at 37 C for 7 days (wet). Data from four experiments was analyzed by ANOVA. All control sample values were in the range of acceptance compared with previous studies. Higher values were obtained for the control groups for flexural strength and modulus compared with the experimental samples. (p < 0.05) There was no statistical difference regarding fracture toughness between control and experimental groups. A statistical difference was observed in Hardness. The experimental group showed higher values under compression.Item Mechanical Properties Of Provisional Restorative Materials(2010) Shimizu Oliva, Graciela, 1976-; Paez de Mendoza, Carmen Y.; Andres, Carl J., 1942-; Brown, David T.; Chu, Tien-Min Gabriel; Levon, John A.A provisional restoration must fulfill biologic, mechanical, and esthetic requirements. These prostheses should provide comfort, pulp protection, positional stability, occlusal function, hygiene access, esthetics, strength and retention. Methyl-methacrylate acrylic has assumed many appli¬cations in the field of restorative dentistry. However, the material still has deficiencies, such as polymerization shrinkage, pulpal damage associated with exothermic polymerization and susceptibility to fracture. Bis-GMA composites, Bis-acryl composites and visible light-cured urethane dimethacrylate resins have been developed to address these issues. The purpose of this study was to compare the mechanical properties of provisional restorations made from composite resins (Protemp Plus, Luxatemp Solar, Radica, Protemp Crown) to those made of the traditional methacrylate resins (Jet, Snap, High Impact). Six groups of samples, two groups from methacrylate and four groups from composite based materials, were fabricated. Samples from each group were evaluated for microhardness (n=10), flexural strength and flexural modulus (n=20) according to ISO 4049, and fracture toughness (n=20) according to ISO 13586. From each of the six groups, ten samples were tested for flexural strength, flexural modulus and fracture toughness and 5 samples were tested for microhardness. These tests were done after storing at 37°C in a distilled water solution for 7 days followed by thermal cycling (2500 cycles, 5-55°C, 45 s. dwell). Identical sets of samples from each group were used as controls; these were tested after storing for 24 hours in dry conditions. The results were analyzed by two-way ANOVA with material type and aging conditions as the two main variables. Significance level was set at p=0.05. For flexural strength and flexural modules, the higher values were obtained for Radica. Protemp plus (7 days) and Radica (24h) had the highest fracture toughness value. Protemp crown showed the highest surface hardness. The mechanical properties of composite resin were superior.Item Nano ceramic fiber reinforced silicone maxillofacial prosthesis(2010) Al-Qenaei, Nouri, 1975-; Levon, John A.; Chu, Tien-Min Gabriel; Hovigitra, Suteera, 1944-; Brown, David T.; Andres, Carl J., 1942-The purpose of this study was to investigate the effect of nano ceramic fiber fillers on the physical properties of VST-50HD silicone maxillofacial prosthesis. Nano alumina fibers at 2 percent, 4-percent, and 6-percent wt were mixed into the VST-50HD silicone elastomer (Factor II Inc., Lakeside, AZ), a commercially-available poly(dimethylsiloxanes). Ten dumb-bell-shaped specimens were used to determine the tensile strength according to ISO 37:2005 and elongation at fracture. Ten trouser-shaped test pieces were used to determine the tear resistance according to ISO 34-1:2004. Shore A test method was used to measure the hardness of the material. The data collected from all quantitative studies of the modified silicones were analyzed using one-way ANOVA with concentration of nano ceramic fiber as the main variable. Specimens from VST- 50HD were also made and tested as control. Results: The mean values for tensile strength (MPa) of control group, 2-percent, 4-percent, and 6-percent reinforced nano ceramic fiber fillers were from 3.43 ± 0.12 to 5.48 ± 0.71. Tear strength (MPa) were from 2.34 ± 0.37 to 5.01 ± 0.39. Elongations at fracture were from 699.66 ± 43.69 to 793.51 ± 57.27. Shore A hardness were from 25.76 ± 2.18 to 38.76 ± 1.83. Conclusion: There was a significant difference (p < 0.001) in the mean tensile, tear and Shore A hardness strengths between the control group and 2-percent, 4-percent, and 6-percent percent reinforced nano ceramic fiber fillers; however, there was not a significant difference (p > 0.05) between 2-percent, 4-percent, and 6-percent reinforced nano ceramic fiber fillers. There was a significant difference (p < 0.001) in the mean elongation at fracture between the 2-percent and control group, 4-percent, and 6-percent reinforced nano ceramic fiber fillers; however, there was not a significant difference (p > 0.05) between control group, 4-percent, and 6-percent reinforced nano ceramic fiber fillers. The properties of the experiment were all lower than the control. Further research is needed to determine the appropriate material and amount of dispersing agent, coupling agent, and determination of the hydprophilicity of the nano ceramic fiber fillers with great emphasis on the dispersing agent.