Browsing by Subject "Resin composite"

Now showing 1 - 3 of 3
  • Thumbnail Image
    Item
    Beam profile characterization of light-emitting-diode curing units and its effect on polymerization of a resin-matrix composite
    (2017) AlZain, Afnan Omar; Platt, Jeffrey A.; Chu, Tien-Min G.; Bottino, Marco C.; Hara, Anderson T.; Goodpaster, John V.; Roulet, Jean-Francois
    The general aim of this study was to investigate the influence of the localized irradiance beam profiles from multiple light-emitting-diode (LED) light-curing units (LCUs) on the polymerization pattern within a resin-matrix composite (RMC). Irradiance beam profiles were generated from one quartz-tungsten-halogen and various single and multiple emission peak LED LCUs using a camera-based beam profiler system combined with LCU power measurements obtained using an integrating sphere/spectrometer assembly. The influence of distance on irradiance, radiant exposure (RE) and degree of conversion (DC) on the top and bottom surfaces of a RMC increment, using various LCUs, at two clinically relevant distances was investigated. Molar absorptivity of the photoinitiators present in the nano-hybrid RMC (Tetric EvoCeram bleaching shade-XL) assessed was using UV-spectrophotometry. The correlation among irradiance, RE and DC was explored. A mapping approach was used to investigate DC, microhardness and cross-link density (CLD) within 5×5×2 mm specimens at various depths; top, 0.5, 0.7, 0.9, 1.1, 1.3,1.5 mm and bottom. The localized irradiance correlation with its corresponding DC, microhardness and CLD was explored, and localized DC correlation with microhardness was assessed. The DC was measured using micro-Raman spectroscopy, and CLD was assessed by an ethanol-softening method (%KHN reduction) using an automated microhardness tester. Molar absorptivity of diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide was 20-fold higher than camphorquinone. Non-uniform LCU beam profiles caused localized polymerization discrepancies that were significant at specific depths and points within the specimens with respect to DC, microhardness and CLD, which did not follow a specific pattern regardless of the LCU or curing distance assessed. A moderate correlation was displayed among irradiance, RE and DC. The localized irradiance from the LCUs was weakly correlated with the corresponding DC, microhardness and CLD on the top surface of a RMC at both curing distances. The localized microhardness was moderately correlated with DC. In conclusion, polymerization within the RMC investigated was non-uniform and did not reflect the LCU irradiance pattern at the area assessed. Also, a mapping approach within the specimens provided a detailed polymerization pattern assessment occurring within a RMC increment. Therefore, the LCUs explored may potentially increase the risk of RMC fracture.
  • Thumbnail Image
    Item
    Effect of post-irradiation polymerization on selected mechanical properties of six direct resins
    (J-STAGE, 2022) Sochacki, Sabrina; Karczewski, Ashley; Platt, Jeffrey; Roberts, Howard W.; Biomedical Sciences and Comprehensive Care, School of Dentistry
    This study evaluated the post-irradiation mechanical property development of six resin composite-based restorative materials from the same manufacturer starting at 1 h post irradiation, followed by 24 h, 1 week, and 1 month after fabrication. Samples were stored in 0.2M phosphate buffered saline until testing. Flexural strength, flexural modulus, flexural toughness, modulus of resiliency, fracture toughness, and surface microhardness were performed at each time interval. Mean data was analyzed by Kruskal Wallis and Dunn's post hoc testing at a 95% level of confidence (α=0.05). Results were material specific but overall, all resin composite material mechanical properties were found to be immature at 1 h after polymerization as compared to that observed at 24 h. It may be prudent that clinicians advise patients, especially those receiving complex posterior composite restorations, to guard against overly stressing these restorations during the first 24 h.
  • Thumbnail Image
    Item
    Influence of curing-light beam profile non-uniformity on degree of conversion and micro-flexural strength of resin-matrix composite
    (2016-10-05) Eshmawi, Yousef Tariq; Platt, Jeffrey A.; Hara, Anderson T.; Diefenderfer, Kim E.; Cook, Norman B.
    Background. Beam profile non-uniformity of light-curing units (LCUs) may result in suboptimal properties of resin-matrix composite (RMC) restorations. Objectives: The objective of this study was to evaluate the effect of curing-light beam profile of multiple light curing units (LCUs) on the degree of conversion (DC) and micro-flexural strength (μ-flexural strength) of RMC. Methods: Forty-five nano-filled hybrid RMC (Tetric EvoCeram, Ivoclar Vivadent, Amherst, NY) specimens were fabricated. Quartz tungsten halogen (QTH) (Optilux 401) (O), multiple emission peak (VALO Cordless) (V) and single emission peak (Demi Ultra) (DU) light-emitting-diode (LED) LCUs were investigated at different light-curing locations (LCLs): 1) the center of the LCU tip; 2) 1.5 mm to the left of the center of the LCU tip; and 3) 1.5 mm to the right of the center of the LCU tip. Specimens were stored wet in deionized water at 37C for 24 hours. The DC was measured on top and bottom surfaces using Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR) spectroscopy. Micro-flexural strength testing was performed using a universal mechanical testing machine at crosshead speed of 1 mm/min. Multi-factorial ANOVAs were used to analyze the data (α = 0.05). Results: All LCUs exhibited significant differences in DC between top and bottom surfaces at the different LCLs. Micro-flexural strength varied with LCL for DU. Conclusions: The non-uniform curing-light beam profile could have a significant effect on μ-flexural strength and DC on top and bottom surfaces of RMC specimens cured at different LCLs.