- Browse by Subject
Browsing by Subject "Dental Porcelain"
Now showing 1 - 2 of 2
Results Per Page
Sort Options
Item Comparative Tensile Strengths of Brackets Bonded to Porcelain with Orthodontic Adhesives and Porcelain Repair Systems(1986) Eustaquio, Robert I.; Garner, LaForrest D.; Barton, Paul; Hennon, David K.; Moore, B. Keith; Muñoz, Carlos; Shanks, James C.This study evaluated the feasibility of bonding brackets to porcelain for orthodontic purposes by measuring and comparing tensile strengths of five silane-based adhesive systems. Each adhesive system bonded mesh pad brackets to 10 glazed and 10 deglazed metal-ceramic crowns and the specimens were then thermocycled between 16 degrees and 56 degrees for 2500 cycles. Clinically relevant bond strengths, comparable to those of adhesives bonding brackets to enamel, were recorded for four of the systems compared. System l+ and Porcelain Primer had the highest mean values followed by Lee's Enamelite 500, then Vivadent's Silanit, Contact-Resin and Isopast, then 3M's Concise and Scotchprime. Most, if not all, failure sites for the four were at the bracket-resin interface. Two-way factorial analysis of variance demonstrated significant differences at P<.001 among the four adhesives but no contribution of surface effect, whether glazed or deglazed, was suggested statistically. Neuman-Keul sequential range tests showed significant differences between System l+ and the three other systems but no significant differences among the three were detected. Den-Mat's Ultrabond recorded extremely low tensile strength values and was of dubious clinical value. A t-test suggested that deglazing porcelain contributed no significant difference in strength compared with intact, glazed porcelain. All failure sites were at the porcelain-resin interface for this product. Since resin may remain bonded to porcelain following debonding, George Taub's diamond polishing paste and Shofu porcelain polishing wheels were compared as to their ability in restoring the porcelain to its original state. Because of the great adhesive bond of the resin to porcelain, craters, pits or tears may be created when resin is cleaned from porcelain with conventional scalers and pliers. The diamond paste gave a better restorative finish than the stones but the end result depended on the extent of original damage following cleaning. Orthodontists should take this point into account when considering bonding to porcelain crowns or veneers for esthetics sake where final risks may outweigh initial benefits. In a limited survey of 100 orthodontists responding to a questionnaire, 89% indicated that they have bonded or contemplated bonding to composite restored teeth, and 83% indicated that they have bonded or contemplated bonding to porcelain.Item Extrinsic Characterization Sustainability in Zirconia Reinforced Lithium Silicate Ceramics(2021-04-08) Gadah, Thrya; May, Jaren; Levon, John; Chu, Tien-Min G; Gregory, Richard; Wei Shao, Lin; Feitosa, SabrinaABSTRACT OBJECTIVE. To investigate the effect of aging on the surface roughness and the color sustainability of externally characterized zirconia reinforced lithium silicate glass-ceramics treated with different surface protocols. METHODS. Sixty blocks (12-mm X 14-mm; 1.5-mm) of pre-crystalized zirconia reinforced-lithium silicate glass-ceramic (Vita Suprinity, Vita Zahnfabrick, Germany) CAD/CAM were crystalized and treated with different surface protocols, as extrinsic characterization (EC), mechanical polishing (MP), glaze layer (GL), surface adjustment (SA) and no treatment – control group (CG). Experimental groups (n=10) were divided as follow: CG; EC-MP-GZ; EC-GZ; EC-MP; EC-GZ-SA-GZ; EC-GZ-SA-MP and submitted to thermocycling (5,000 cycles, 5-55C) and toothbrushing simulation (5,000 cycles). Surface roughness (Ra and Rq), color change (CIED2000) and biofilm growth were evaluated. Statistical analysis was performed with a two-sided 5% significance level for all tests. RESULTS. For the parameter RaX, the control differed from EC-GZ and EC-MP (p = 0.04). For the parameter RqX, EC-GZ presented higher surface roughness compared than EC-MP-GZ and the group EC-GZ-SA-MP (p=0.02). EC-MP (p<0.01) and the EC-GZ-SA-MP (p<0.01) showed higher color change E00 after aging, while CG and EC-MP-GZ the least. For the biofilm growth, no significant group effect on bacteria counts was found (p=0.089). CONCLUSION. The aging protocol affected the surface roughness, and color of externally characterized zirconia reinforced lithium silicate glass-ceramics submitted to different surface treatment protocols. In the present study, when the mechanical polishing was performed before glaze application, the slightest color change and surface roughness were observed compared to the other surface treatments. Bacteria were not able to grow in the material surface, under the conditions tested in the present study.