Browsing by Author "Shrestha, Sudhir"

Now showing 1 - 10 of 12
  • Thumbnail Image
    Item
    Breast Cancer Detection via Microwave Imaging
    (Office of the Vice Chancellor for Research, 2011-04-08) Reid, Joshua R.N.; Ghane, Parvin; Shrestha, Sudhir; Agarwal, Mangilal; Varahramyan, Kody
    Breast cancer is one of the major common diseases among women and takes about 40,000 lives every year. Early detection of breast cancer greatly increases the chance of survival. The norm for today’s detection of breast cancer consists of mammograms, magnetic resonance imaging (MRI), and ultrasonic examination. Unfortunately, the process is a fraction of completeness despite its feeling of discomfort, high cost, and exposure to ionizing radiation which poses cumulative side effects respectively. The present research investigates the efficiency and implementation of microwave imaging to be used in the detection of breast cancer. Microwave imaging (MWI) is a process that illuminates the breast with microwave signals, and receives and analyses scattered signals for breast cancer detection and imaging. The electromagnetic waves that are scattered within the breast provide information that are transmitted and received via microstrip patch antennas, providing an image of detected lesions. In the presented poster, design of a patch antenna and simulation results are presented. In the event of designing, the overall goal was to obtain a voltage standing wave ratio (VSWR) less than 2 at 2.4 GHz signal frequency. To receive the intended results, the dimensions and design of the microstrip patch were important factors given the substrate parameters. Currently, the project is in the prototyping stage for the validation of simulation results and further optimization and development of the antenna for microwave breast cancer detection and imaging applications.
  • Thumbnail Image
    Item
    Cross-Selectivity Enhancement of Poly(vinylidene fluoride-hexafluoropropylene)-Based Sensor Arrays for Detecting Acetone and Ethanol
    (MDPI, 2017-03-15) Daneshkhah, Ali; Shrestha, Sudhir; Siegel, Amanda; Varahramyan, Kody; Agarwal, Mangilal; Electrical and Computer Engineering, School of Engineering and Technology
    Two methods for cross-selectivity enhancement of porous poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP)/carbon black (CB) composite-based resistive sensors are provided. The sensors are tested with acetone and ethanol in the presence of humid air. Cross-selectivity is enhanced using two different methods to modify the basic response of the PVDF-HFP/CB sensing platform. In method I, the adsorption properties of PVDF-HFP/CB are altered by adding a polyethylene oxide (PEO) layer or by treating with infrared (IR). In method II, the effects of the interaction of acetone and ethanol are enhanced by adding diethylene carbonate (DEC) or PEO dispersed in DEC (PEO/DEC) to the film. The results suggest the approaches used in method I alter the composite ability to adsorb acetone and ethanol, while in method II, they alter the transduction characteristics of the composite. Using these approaches, sensor relative response to acetone was increased by 89% compared with the PVDF-HFP/CB untreated film, whereas sensor relative response to ethanol could be decreased by 57% or increased by 197%. Not only do these results demonstrate facile methods for increasing sensitivity of PVDF-HFP/CB film, used in parallel they demonstrate a roadmap for enhancing system cross-selectivity that can be applied to separate units on an array. Fabrication methods, experimental procedures and results are presented and discussed.
  • Thumbnail Image
    Item
    Cross-Selectivity Enhancement of Poly(vinylidene fluoride-hexafluoropropylene)-Based Sensor Arrays for Detecting Acetone and Ethanol
    (MDPI, 2017-03-15) Daneshkhah, Ali; Shrestha, Sudhir; Siegel, Amanda; Varahramyan, Kody; Agarwal, Mangilal; Mechanical Engineering, School of Engineering and Technology
    Two methods for cross-selectivity enhancement of porous poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP)/carbon black (CB) composite-based resistive sensors are provided. The sensors are tested with acetone and ethanol in the presence of humid air. Cross-selectivity is enhanced using two different methods to modify the basic response of the PVDF-HFP/CB sensing platform. In method I, the adsorption properties of PVDF-HFP/CB are altered by adding a polyethylene oxide (PEO) layer or by treating with infrared (IR). In method II, the effects of the interaction of acetone and ethanol are enhanced by adding diethylene carbonate (DEC) or PEO dispersed in DEC (PEO/DEC) to the film. The results suggest the approaches used in method I alter the composite ability to adsorb acetone and ethanol, while in method II, they alter the transduction characteristics of the composite. Using these approaches, sensor relative response to acetone was increased by 89% compared with the PVDF-HFP/CB untreated film, whereas sensor relative response to ethanol could be decreased by 57% or increased by 197%. Not only do these results demonstrate facile methods for increasing sensitivity of PVDF-HFP/CB film, used in parallel they demonstrate a roadmap for enhancing system cross-selectivity that can be applied to separate units on an array. Fabrication methods, experimental procedures and results are presented and discussed.
  • Thumbnail Image
    Item
    FABRICATION OF A THIN FILM SOLAR CELLS USING LAYER BY LAYER (LBL) NANOASSEMBLY OF COPPER INDIUM GALLUIM SELENIUM (CIGS) NANOPARTICLES
    (Office of the Vice Chancellor for Research, 2012-04-13) Ghane, Parvin; Hemati, Azadeh; Shrestha, Sudhir; Agarwal, Mangilal; Varahramyan, Kody
    Copper Indium Gallium Selenium (CIGS), a p-type semiconductor material with a tunable band gap, has been broadly studied for high efficiency solar cells as a viable sustainable energy source. Production of CIGS nanoparticles gives the ability of fabricating thin, light, and flexible solar cells. However, the current fabrication technologies of such devices are still very costly. This poster presents the synthesis and functionalization of CIGS nanoparticles and proposes Layer-by-Layer (LbL) nanoassembly process, as a low cost method, to fabricate thin films for solar cell applications. The results show that the synthesized CIGS particles have 1.3 ev band gap and 30 nm diameter in av-erage. These particles were later coated with polymers to provide alternative opposite surface charges suitable for LbL process. Deposition of 20 layers of the particles on indium tinoxide (ITO) coated glass formed a thin film with 220 nm thickness. The measured current voltage (I-V) characteristic of the film gave resistivity of 7.9 MΩ.m in dark and 2.25 MΩ.m under light illumina-tion. A prototype solar cell made out of the film resulted in short circuit cur-rent density (JSC) of 0.3 mA/cm2 and open circuit voltage (VOC) of 0.7 V.
  • Thumbnail Image
    Item
    Layer-By-Layer Self-Assembly of CIGS Nanoparticles and Polymers for All-Solution Processable Low-Cost, High-Efficiency Solar Cells
    (Office of the Vice Chancellor for Research, 2013-04-05) Ho, Tung; Vittoe, Robert; Kakumanu, Namratha; Shrestha, Sudhir; Agarwal, Mangilal; Varahramyan, Kody
    Thin film solar cells made from copper indium gallium selenide (CIGS) materials have shown great potentials of providing low cost, high efficiency panels viable for wide spread commercial usage. Layer-by-layer (LbL) self-assembly is a low-cost, versatile nanofilm deposition process, however introduces polymers in the nanoparticles films, which reduces charge transport thereby affecting solar cell efficiency. This research aims to study various polymer materials to replace currently used insulating polymers in LbL, such as poly(sodium-4-styrenesulfonate) (PSS) and polyethyenimine (PEI). This poster will present processes and results of CIGS nanoparticles synthesis using controlled heating of CuCl, InCl3, GaCl3, and Se in oleyamine; functionalization of the particles to disperse in organic and aqueous-based solvents for LbL; and initial outcomes of CIGS, polymers LbL film fabrication and characterization. The size distribution of synthesized nanoparticles cleaned through alternate suspension and precipitation in chloroform and ethanol shows a peak at 72 nm. Particles light absorption properties measured with ultraviolet-visible-near infrared (UV-Vis-NIR) spectroscopy shows good spectrum coverage with band edge near 1100 nm. The X-ray diffraction (XRD) results of the particles confirms the composition and tetragonal chalcopyrite crystal structure of CIGS materials. Chemical-bath-deposition of cadmium sulfide (CdS) and spray-coating of zinc oxide (ZnO) films are used along with LbL absorbing film in realization of a solar cell device. The fabricated devices are tested using semiconductor characterization instrument.
  • Thumbnail Image
    Item
    Low-Power ASIC Design for Multiple Integrated Sensors Applications
    (Office of the Vice Chancellor for Research, 2013-04-05) Jafarian, Hossein; Daneshkhah, Ali; Shrestha, Sudhir; Agarwal, Mangilal; Rizkalla, Maher; Varahramyan, Kody
    The aim of this work is to develop sensor integrated low-power chip for biomedical and other applications. Complementary metal-oxide-semiconductor (CMOS) technology in integrated circuit (IC) design has been applied to develop application specific integrated circuits (ASIC). An ASIC design that includes analog and digital sub-systems for various applications forming a system on chip (SoC) is presented. The analog sub-system drives multiple sensors, while the digital sub-system manages power, sensors, and signal output. A frequency of the pulse signals generated by the analog sub-system depends on the input voltage, which in-turn varies with sensor parameters. The frequency change of 750 MHz to 1 GHz was observed for input voltage variations of 1.2 to 2.2 V, with sensitivity of 10 mV. A separate temperature sensor included in the analog sub-system demonstrated frequency change of 830 to 440 MHz for temperature variations of ˗50°C to 100°C with resolution of 1°C. The output signal in digital sub-system is generated by counting the input pulses for each clock which has ‘on-state’ of only 3/16 seconds. This results in a significant reduction in the power consumption. This poster presents and discusses the system design and simulation results.
  • Thumbnail Image
    Item
    Low-power ASIC design with integrated multiple sensor system
    (2013-08) Jafarian, Hossein; Varahramyan, Kody; Rizkalla, Maher E.; Agarwal, Mangilal; Shrestha, Sudhir; King, Brian
    A novel method of power management and sequential monitoring of several sensors is proposed in this work. Application specific integrated circuits (ASICs) consisting of analog and digital sub-systems forming a system on chip (SoC) has been designed using complementary metal-oxide-semiconductor (CMOS) technology. The analog sub-system comprises the sensor-drivers that convert the input voltage variations to output pulse-frequency. The digital sub-system includes the system management unit (SMU), counter, and shift register modules. This performs the power-usagemanagement, sensor-sequence-control, and output-data-frame-generation functions. The SMU is the key unit within the digital sub-system is that enables or disables a sensor. It captures the pulse waves from a sensor for 3 clocks out of a 16-clock cycle, and transmits the signal to the counter modules. As a result, the analog sub-system is at on-state for only 3/16th fraction (18 %) of the time, leading to reduced power consumption. Three cycles is an optimal number selected for the presented design as the system is unstable with less than 3 cycles and higher clock cycles results in increased power consumption. However, the system can achieve both higher sensitivity and better stability with increased on-state clock cycles. A current-starved-ring-oscillator generates pulse waves that depend on the sensor input parameter. By counting the number of pulses of a sensor-driver in one clock cycle, a sensor input parameter is converted to digital. The digital sub-system constructs a 16-bit frame consisting of 8-bit sensor data, start and stop bits, and a parity bit. Ring oscillators that drive capacitance and resistance-based sensors use an arrangement of delay elements with two levels of control voltages. A bias unit which provides these two levels of control voltages consists of CMOS cascade current mirror to maximize voltage swing for control voltage level swings which give the oscillator wider tuning range and lower temperature induced variations. The ring oscillator was simulated separately for 250 nm and 180 nm CMOS technologies. The simulation results show that when the input voltage of the oscillator is changed by 1 V, the output frequency changes linearly by 440 MHz for 180 nm technology and 206 MHz for 250 nm technology. In a separate design, a temperature sensitive ring oscillator with symmetrical load and temperature dependent input voltage was implemented. When the temperature in the simulation model was varied from -50C to 100C the oscillator output frequency reduced by 510 MHz for the 250 nm and by 810 MHz for 180 nm CMOS technologies, respectively. The presented system does not include memory unit, thus, the captured sensor data has to be instantaneously transmitted to a remote station, e.g. end user interface. This may result in a loss of sensor data in an event of loss of communication link with the remote station. In addition, the presented design does not include transmitter and receiver modules, and thus necessitates the use of separate modules for the transfer of the data.
  • Thumbnail Image
    Item
    Paper-Based Flexible Lithium-Ion Batteries
    (Office of the Vice Chancellor for Research, 2014-04-11) Aliahmad, Nojan; Shrestha, Sudhir; Agarwal, Mangilal; Varahramyan, Kody
    Paper-based flexible batteries have a wide range of applications in paper-based platforms, including in paper electronics, packaging, product displays, greeting cards, and sensors. This poster will present lithium-ion batteries using flexible paper-based current collectors. These current collectors were fabricated from wood microfibers that were coated with carbon nanotubes (CNT) through an electrostatic layer-by-layer nanoassembly process. The use of paper-based current collectors provides flexibility and improved electrode adhesion. Electrodes were fabricated by casting thin layers of lithium titanium oxide, lithium cobalt oxide or lithium magnesium oxide on the conductive paper. Half-cell and full-cell devices were fabricated and tested. The results show that the presented batteries use reduced mass loading of carbon nanotubes (10.1 μg/cm2) compared to CNT film based batteries. Experimental capacities of the half-cell devices were measured to be 150 mAh/g for lithium cobalt oxide, 158 mAh/g for lithium titanium oxide, and 130 mAh/g for lithium magnesium oxide. Device designs, fabrication processes of paper-based current collectors, electrodes, and batteries, and further experimental results, including solid electrolytes, will be presented.
  • Thumbnail Image
    Item
    Paper-based lithium-Ion batteries using carbon nanotube-coated wood microfiber current collectors
    (2013-11-06) Aliahmad, Nojan; Varahramyan, Kody; Agarwal, Mangilal; Shrestha, Sudhir; Rizkalla, Maher E.; King, Brian
    The prevalent applications of energy storage devices have incited wide-spread efforts on production of thin, flexible, and light-weight lithium-ion batteries. In this work, lithium-ion batteries using novel flexible paper-based current collectors have been developed. The paper-based current collectors were fabricated from carbon nanotube (CNT)-coated wood microfibers (CNT-microfiber paper). This thesis presents the fabrication of the CNT-microfiber paper using wood microfibers, coating electrode materials, design and assemblies of battery, testing methodologies, and experimental results and analyses. Wood microfibers were coated with carbon nanotubes and poly(3,4-ethylenedioxythiophene) (PEDOT) through an electrostatic layer-by-layer nanoassembely process and formed into a sheet, CNT-microfiber paper. The CNT loading of the fabricated paper was measured 10.1 μg/cm2 subsequently considered. Electrode material solutions were spray-coated on the CNT-microfiber paper to produce electrodes for the half and full-cell devices. The CNT current collector consists of a network structure of cellulose microfibers at the micro-scale, with micro-pores filled with the applied conductive electrode materials reducing the overall internal resistance for the cell. A bending test revealed that the paper-based electrodes, compared to metal ones, incurred fewer damages after 20 bends at an angle of 300o. The surface fractures on the paper-based electrodes were shallow and contained than metallic-based electrodes. The micro-pores in CNT-microfiber paper structure provides better adherence to the active material layer to the substrate and inhibits detachment while bending. Half-cells and full-cells using lithium cobalt oxide (LCO), lithium titanium oxide (LTO), and lithium magnesium oxide (LMO) were fabricated and tested. Coin cell assembly and liquid electrolyte was used. The capacities of half-cells were measured 150 mAh/g with LCO, 158 mAh/g with LTO, and 130 mAh/g with LMO. The capacity of the LTO/LCO full-cell also was measured 126 mAh/g at C/5 rate. The columbic efficiency of the LTO/LCO full-cell was measured 84% for the first charging cycle that increased to 96% after second cycle. The self-discharge test of the full-cell after charging to 2.7 V at C/5 current rate is showed a stable 2 V after 90 hours. The capacities of the developed batteries at lower currents are comparable to the metallic electrode-based devices, however, the capacities were observed to drop at higher currents. This makes the developed paper-based batteries more suitable for low current applications, such as, RFID tags, flexible electronics, bioassays, and displays. The capacities of the batteries at higher current can be improved by enhancing the conductivity of the fibers, which is identified as the future work. Furthermore, fabrication of an all solid state battery using solid electrolyte is also identified as the future work of this project.
  • Thumbnail Image
    Item
    Paper-Based Lithium-Ion Battery
    (Office of the Vice Chancellor for Research, 2013-04-05) Aliahmad, Nojan; Agarwal, Mangilal; Shrestha, Sudhir; Varahramyan, Kody
    Lithium-ion batteries have a wide range of applications including present day portable consumer electronics and large-scale energy storage. Realization of these batteries in flexible, light-weight forms will further expand the usage in current and future innovative electronic devices. Lithium titanium oxide (Li4Ti5O12), lithium magnesium oxide (LiMn2O4) and lithium cobalt oxide (LiCoO2) materials have been consistently studied for application in high capacity batteries, and thus considered in the devices that are presented in the poster. Carbon nanotube (CNT) coated wood microfiber papers are used as current collectors, which provide high surface area, flexibility, and texture of paper, with low CNT utilization (10.1μg/cm2). The CNT microfiber paper is fabricated by layer-by-layer (LbL) nano-assembly of CNT over cellulose microfibers. Results from paper-based half-cell batteries show capacities of 130 mAh/g for LiMn2O4, 150 mAh/g for LiCoO2, and 158 mAh/g for Li4Ti5O12 at C/5 rate. These results are comparable with metallic electrode based cells. The fabrication of CNT microfiber paper, assembly of batteries, experimental methods, and results are presented and discussed.