Browsing by Author "Roberts, W. Eugene, Jr."
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item Evaluation of the Tensile Bond Strength of Orthodontic Bracket Bases Using Glass Ionomer Cement as an Adhesive(1992) Burns, Richard D., Jr.; Roberts, W. Eugene, Jr.; Garetto, Lawrence P.; Moore, B. Keith; Miller, James R.; Shanks, James C., Jr.; Hennon, David K.The search for an orthodontic bonding adhesive that has chemical adhesion to enamel and releases fluoride into the oral environment has led to experimentation with glass ionomer cements. This study compared the tensile bond strength of eight different orthodontic bracket base designs in vitro and assessed the amount of adhesive remaining on the bracket pad after debonding. Each bracket base design included in this study had unique characteristics warranting their inclusion. The groups contained brackets with 60, 80, and 100 gauge mesh pads; 100 gauge mesh sandblasted pads; perforated metal bases; Micro-Lock™ photo-etched bases; Dyna-Lock™ integral bracket/bases; and ceramic silane-coated bracket pads. Groups contained 20 to 22 specimens that were bonded to bovine incisor teeth embedded in a self-curing acrylic block that could be held in the testing machine. Pre-encapsulated glass ionomer cement (Ketac-Fil™) was the experimental adhesive. The adhesive was mixed according to the manufacturer's instructions in a dental amalgamator. The specimens were thermocycled between water oaths of 15°C and 55°C. The specimens spent 30 seconds in each bath for a total of 2,500 cycles and were stored in a humidor until debonding. After 14 days, the specimens were subjected to a tensile force using an Instron mechanical testing machine until failure occurred. The Micro-Loc™ photo-etched base had significantly higher mean tensile bond strength (p<0.05) than all other brackets tested. The ceramic brackets were unable to be tested due to the extremely weak bond strength which did not allow preparation of the samples for debonding. Following debonding, the percentage of adhesive remaining attached to the bracket base was determined using a grid in the ocular of a light microscope. In general, the site of bond failure involved the base/adhesive interface. The Dyna-Lock™ integral bracket/base and 80 gauge mesh base had a greater mean percent of adhesive remaining attached to the base. (Dyna-Lock™ 45 percent and 80 gauge mesh 43 percent vs. all other < 20 percent.) The results indicate that the bracket base design can influence the bond strength when GIC is used as an orthodontic adhesive and suggests that development of GIC with increased fracture toughness might increase bond strength.Item Histomorphometric and Biomechanical Analyses of Osseointegration of Four Different Orthodontic Mini Implant Surfaces(2011) Yadav, Sumit; Roberts, W. Eugene, Jr.; Chen, Jie; Katona, Thomas R.; Liu, Sean S.; Huja, Sarandeep S. (Sarandeep Singh), 1965-Objective: To evaluate the osseointegration potential of four different surfaces of mini-implants .We hypothesized that mini-implants surface roughness alters the intrinsic biomechanical properties of the bone integrated to titanium. Materials and Methods: Mini implants and circular discs were made from alloy Ti6Al4V grade 5. On the basis of surface treatment study was divided into 4 groups: Group 1: Machined: no surface treatment, Group 2: Acid etched: with hydrochloric acid, Group 3: Grit Blasted with alumina and Group 4: Grit blasted +Acid etched. Surface roughness parameters (mean surface roughness: Ra and Quadratic Average roughness: Rq) of the four discs from each group were measured by the optical profilometer. Contact angle measurement of 3 discs from each group was done with a Goniometer. Contact angle of liquids with different hydrophobicity and hydrophilicity were measured. 128 mini implants, differing in surface treatment, were placed into the tibias and femurs of 8 adult male New Zealand white rabbits. Biomechanical properties (Removal torque and hardness) measurements and histomorphometric observations were measured. Results: Ra and Rq of groups were: Machined (1.17±0.11, 2.59±0.09) Acid etched (1.82±0.04, 3.17±0.13), Grit blasted (4.83±0.23, 7.04±0.08), Grit blasted + Acid etched (3.64±0.03, 4.95±0.04) respectively. Group 4 had significantly (p=0.000) lower Ra and Rq than Group 3. The interaction between the groups and liquid was significant. Group 4 had significantly lower contact angle measurements (40.4°, 26.9°), both for blood and NaCl when compared to other three groups (p≤0.01). Group 4 had significantly higher torque than Group 3 (Tibia: 13.67>9.07N-cm; Femur: 18.21>14.12N-cm), Group 4 (Tibia: 13.67>9.78N-cm; Femur: 18.21>12.87N-cm), and machined (Tibia: 13.67>4.08N-cm; Femur: 18.21>6.49N-cm). SEM analysis reveals significantly more bone implant gap in machined implant surfaces than treated implant surfaces. Bone to implant contact had significantly higher values for treated mini implant surface than machined surface. Hardness of the bone near the implant bone interface is 20 to 25% less hard than bone 1mm away from it in both Femur and Tibia. Conclusion: Surface roughness and wettability of mini implants influences their biological response. Grit blasted and acid etched mini implants had lowest contact angle for different liquids tested and highest removal torques.Item Orthodontic Mechanotransduction and the Role of the P2X7 Receptor(2009) Viecilli, Rodrigo F.; Katona, Thomas R.; Chen, Jie; Roberts, W. Eugene, Jr.; Hartsfield, James K., Jr.; Bidwell, JosephThe first part of the study describes the development of a microCT based engineering model to study orthodontic responses. The second part investigated the relationship between orthodontic stimulus, root resorption and bone modeling. It was hypothesized that stress magnitudes are insufficient to portray the mechanical environment and explain the clinical response; directions also play a role. An idealized tooth model was constructed for finite element analysis. The principal stress magnitudes and directions were calculated in tipping and translation. It was concluded that within the same region of root, PDL and bone, there can be compression in one structure, tension in another. At a given point in a structure, compression and tension can coexist in different directions. Magnitudes of compression or tension are typically different in different directions. Previously published data presenting only stress magnitude plots can be confusing, perhaps impossible to understand and/or correlate with biological responses. To avoid ambiguities, a reference to a principal stress should include its predominant direction. Combined stress magnitude/direction results suggest that the PDL is the initiator of mechanotransduction. The third part of this project tested the role of the P2X7 receptor in the dentoalveolar morphology of C57B/6 mice. P2X7R KO (knockout) mice were compared to C57B/6 WT to identify differences in a maxillary molar and bone. Tooth dimensions were measured and 3D bone morphometry was conducted. No statistically significant differences were found between the two mouse types. P2X7R does not have a major effect on alveolar bone or tooth morphology. The final part examines the role of the P2X7 receptor in a controlled biomechanical model. Orthodontic mechanotransduction was compared in wild-type (WT) and P2X7R knock-out (KO) mice. Using Finite Element Analysis, mouse mechanics were scaled to produce typical human stress levels. Relationships between the biological responses and the calculated stresses were statistically tested and compared. There were direct relationships between certain stress magnitudes and root resorption and bone formation. Hyalinization and root and bone resorption were different in WT and KO. Orthodontic responses are related to the principal stress patterns in the PDL and the P2X7 receptor plays a significant role in their mechanotransduction.