Browsing by Author "Platt, J. A."

Now showing 1 - 2 of 2
  • Thumbnail Image
    Item
    The Influence of Distance on Radiant Exposure and Degree of Conversion Using Different Light-Emitting-Diode Curing Units
    (Allen Press, 2019-05) Al-Zain, A.O.; Eckert, G. J.; Platt, J. A.; Biomedical Sciences and Comprehensive Care, School of Dentistry
    Objectives: To investigate the influence of curing distance on the degree of conversion (DC) of a resin-based composite (RBC) when similar radiant exposure was achieved using six different light-curing units (LCUs) and to explore the correlation among irradiance, radiant exposure, and DC. Methods and Materials: A managing accurate resin curing-resin calibrator system was used to collect irradiance data for both top and bottom specimen surfaces with a curing distance of 2 mm and 8 mm while targeting a consistent top surface radiant exposure. Square nanohybrid-dual-photoinitiator RBC specimens (5 × 5 × 2 mm) were cured at each distance (n=6/LCU/distance). Irradiance and DC (micro-Raman spectroscopy) were determined for the top and bottom surfaces. The effect of distance and LCU on irradiance, radiant exposure, and DC as well as their linear associations were analyzed using analysis of variance and Pearson correlation coefficients, respectively (α=0.05). Results: While maintaining a similar radiant exposure, each LCU exhibited distinctive patterns in decreased irradiance and increased curing time. No significant differences in DC values (63.21%-70.28%) were observed between the 2- and 8-mm distances, except for a multiple-emission peak LCU. Significant differences in DC were detected among the LCUs. As expected, irradiance and radiant exposure were significantly lower on the bottom surfaces. However, a strong correlation between irradiance and radiant exposure did not necessarily result in a strong correlation with DC. Conclusions: The RBC exhibited DC values >63% when the top surface radiant exposure was maintained, although the same values were not reached for all lights. A moderate-strong correlation existed among irradiance, radiant exposure, and DC.
  • Thumbnail Image
    Item
    Monitoring of sound and carious surfaces under sealants over 44 months
    (SAGE Publications, 2014-11) Fontana, M.; Platt, J. A.; Eckert, G. J.; González-Cabezas, C.; Yoder, K.; Zero, D. T.; Ando, M.; Soto-Rojas, A. E.; Peters, M. C.; Department of Restorative Dentistry, IU School of Dentistry
    Although there is strong evidence for the effectiveness of sealants, one major barrier in sealant utilization is the concern of sealing over active caries lesions. This study evaluated detection and monitoring of caries lesions through a clear sealant over 44 mo. Sixty-four 7- to 10-year-old children with at least 2 permanent molars with International Caries Detection and Assessment System (ICDAS) scores 0-4 (and caries less than halfway through the dentin, radiographically) were examined with ICDAS, DIAGNOdent, and quantitative light-induced fluorescence (QLF) before sealant placement and 1, 12, 24, and 44 mo (except QLF) after. Bitewing radiographs were taken yearly. DIAGNOdent and QLF were able to distinguish between baseline ICDAS before and after sealant placement. There was no significant evidence of ICDAS progression at 12 mo, but there was small evidence of minor increases at 24 and 44 mo (14% and 14%, respectively) with only 2% ICDAS ≥ 5. Additionally, there was little evidence of radiographic progression (at 12 mo = 1%, 24 mo = 3%, and 44 mo = 9%). Sealant retention rates were excellent at 12 mo = 89%, 24 mo = 78%, and 44 mo = 70%. The small risk of sealant repair increased significantly as baseline ICDAS, DIAGNOdent, and QLF values increased. However, regardless of lesion severity, sealants were 100% effective at 12 mo and 98% effective over 44 mo in managing occlusal surfaces at ICDAS 0-4 (i.e., only 4 of 228 teeth progressed to ICDAS ≥ 5 associated with sealants in need of repair and none to halfway or more through the dentin, radiographically). This study suggests that occlusal surfaces without frank cavitation (ICDAS 0-4) that are sealed with a clear sealant can be monitored with ICDAS, QLF, or DIAGNOdent, which may aid in predicting the need for sealant repair.