Browsing by Author "Kelly, Adam B."

Now showing 1 - 3 of 3
  • Thumbnail Image
    Item
    3D-Image Analysis of the Impact of Toothpaste Abrasivity on the Progression of Simulated Non-Carious Cervical Lesions
    (Elsevier, 2018) Sabrah, Alaa H.; Turssi, Cecilia P.; Lippert, Frank; Eckert, George J.; Kelly, Adam B.; Hara, Anderson T.; Cariology, Operative Dentistry and Dental Public Health, School of Dentistry
    Objectives To investigate the effect of toothpaste abrasive level on the progression of non-carious cervical lesions (NCCLs) using 3D-image subtraction. Methods Upper first premolars were allocated into seven groups (n = 16) of toothpaste/abrasive slurries: A-Zeodent113/5%, B-Zeodent124/10%, C-Zeodent103/15%, D-Sensodyne Pronamel, E-Crest Cavity-Protection, F-Crest Pro-Health-Whitening, and G-Deionized water (DIW). Teeth were mounted on acrylic blocks, and their root surfaces covered with acrylic resin, except for 2-mm near the cemento-enamel junction that was exposed to toothbrushing. Specimens were brushed with the slurries for 5000-, 15,000-, 35,000- and 65,000-strokes. Impressions were taken at baseline and after each brushing time, and then scanned by a 3D optical profilometer. Dentine volume loss was calculated by image subtraction software and subjected to mixed-model ANOVA and multiple comparison tests (α = 0.05). Results No significant differences among slurries were observed at 5000 and 15,000. At 35,000, F showed higher loss than all other groups except C, which did not differ from the others. At 65,000, F (4.19 ± 3.29 mm3) showed the highest loss, followed by C (2.33 ± 1.47 mm3), which differed from all the other groups except B (1.85 ± 0.91 mm3). Groups B, A (1.35 ± 0.65 mm3), D (1.17 ± 0.48 mm3), E (1.40 ± 0.68 mm3) and G (1.12 ± 0.73 mm3) did not differ from each other. Groups F and C showed significant increase of volume loss starting at 35,000, while B, A, D and E only at 65,000; no increase loss was observed for G. Conclusions 3D-image subtraction was able to quantify and differentiate tooth loss, but only at advanced stages. The progression of NCCLs was more evident and faster for highly abrasive slurries. Clinical significance Upon root dentin exposure, brushing with lower abrasive dentifrices is advisable to reduce the risk for NCCLs development.
  • Thumbnail Image
    Item
    Comparison Between Radiotracer and Surface Profile Methods for the Determination of Dentifrice
    (Office of the Vice Chancellor for Research, 2013-04-05) Sabrah, Alaa; Lippert, Frank; Kelly, Adam B.; Hara, Anderson T.
    Introduction: ISO11609 states that a surface profile (Sp) method can be used to determine dentifrice abrasivity in relation to dentin (RDA) as an alternative to the traditional radiotracer method (Rt). A comparison between both methods was performed in this study. Methods: Specimens from human root dentin were prepared for each method and randomly assigned to 8 dentifrice/abrasive groups (n=8), which represented a wide abrasivity range. Aqueous dentifrice slurries or abrasive suspensions in a solution containing 0.5% carboxymethylcellulose and 10% glycerin were used to brush specimens in a custom-made V-8 cross-brushing machine. Two independent studies (Sp, Rt) were carried out. For Rt, the specimen preparation, study design, analysis and calculation of the abrasive level (RDA) followed the ISO11609/Annex A guidelines. Similarly for Sp, the ISO11609/Annex B recommendations were followed, except by the number of brushing strokes, which was pre-determined to be 2000 strokes (instead of 10000) in a preliminary test. Data were analyzed using ANOVA and Tukey tests, with significance level set at 5%. The correlation between methods was also investigated. Results: Overall, higher variation and RDA values were observed for the Sp method compared to Rt. While good correlation was found between methods (R2=0.841), group ranking was dissimilar and better statistical differentiation among groups was observed in Rt. Conclusions: The Rt method showed to be a more standardized and robust method compared to Sp for the determination of RDA values of dentifrices/abrasives. Sp needs to be further developed before being considered as an equivalent test method for RDA. The determination of the abrasive levels of toothpastes using standard testing methods is important to guide oral care professionals and patients on the prevention of toothbrushing abrasive wear.
  • Thumbnail Image
    Item
    Exploratory Analysis of Objective Outcome Measures for the Clinical Assessment of Erosive Tooth Wear
    (MDPI, 2023-08-02) Romero, Maria Jacinta Rosario H.; Ungar, Peter S.; Fried, Daniel; Lippert, Frank; Zero, Domenick T.; Zunt, Susan; Eckert, George J.; Gutierrez Gossweiler, Ana; Elkington-Stauss, Dylan Jacob; Tamayo-Cabeza, Guillermo; Kelly, Adam B.; Bartels, Troy; Kita, Camille; Wewers, Elizabeth; Hara, Anderson T.; Cariology, Operative Dentistry and Dental Public Health, School of Dentistry
    This study proposed using enamel surface texture and thickness for the objective detection and monitoring of erosive tooth wear (ETW), comparing them to the standard subjective Basic Erosive Wear Evaluation (BEWE). Thirty-two subjects (n = 597 teeth) were enrolled in this longitudinal observational clinical study. Enamel thickness (by cross-polarization optical coherence tomography, CP-OCT) and 3D dental microwear parameters, i.e., area-scale fractal complexity (Asfc), anisotropy (Str), and roughness (Sa) (by white-light scanning confocal profilometry), were obtained from buccal surfaces. Buccal, occlusal, and lingual surfaces were scored for BEWE and the maximum score per tooth (BEWEMax) was determined at baseline and 12 months (M12). Data outcome relationships were evaluated (alpha = 0.05). Enamel thickness decreased (p < 0.001), BEWE scores, Sa, and Str increased (p < 0.001), while Asfc did not change at M12. Baseline BEWEBuccal correlated strongly with BEWEMax (r = 0.86, p < 0.001) and moderately with BEWELingual (r = 0.42, p < 0.001), but not with enamel thickness (r = 0.03, p = 0.43). Change (Δ) in surface texture outcomes correlated poorly but significantly with ΔBEWEBuccal (r = −0.15–0.16, p < 0.001) and did not correlate with Δenamel thickness (r = 0.02–0.09, p > 0.06). Teeth with BEWE progression revealed a greater increase in ΔSa and ΔStr. These findings suggest that enamel surface roughness can potentially determine ETW severity, and CP-OCT may be relevant for clinically monitoring enamel thickness.