Browsing by Author "Hovijitra, Suteena, 1944-"

Now showing 1 - 3 of 3
  • Thumbnail Image
    Item
    The effect of a novel photoinitiator system (RAP) on dental resin composites' flexural strength, polymerization stress, and degree of conversion
    (2009) Schaub, Kellie; Platt, Jeffrey A., 1958-; Andres, Carl J., 1942-; Levon, John A.; Brown, David; Hovijitra, Suteena, 1944-
    Objectives: A new technology has been introduced into the field of dental resin composites that professes to enhance light-curing efficiency. Rapid amplified photopolymerization (RAP) initiator technology has not yet been fully compared with resin composites with conventional initiators such as camphorquinone (CQ). The purpose of this study was to compare and contrast the effects of this novel technology (RAP) on properties of two light-cured resin composites. Flowable (EFQ) and microfilled (ESQ) experimental composites were fabricated and supplied from Tokuyama Dental with (w/RAP) and without RAP (w/o RAP). The flexural strength (MPa) and flexural modulus (MPa) were obtained using a three-point bending apparatus (Sintech Renew 1123, Instron Engineering Corp., Canton, MA). Polymerization stress curves were created using a tensometer (American Dental Association Health Foundation, NIST, Gaithersburg, MD) which were then used to calculate the maximum stress rate. Finally, the degree of conversion was measured using infrared spectroscopy (Jassco FT-IR spectrometer, Model: 4100, Jasco Corporation, Tokyo, Japan). When evaluating the flexural strength, the peak stress for EFQ w/RAP was significantly higher than EFQ w/o RAP (p = 0.0001). This was statistically not significant for the ESQ group, even though ESQ w/RAP did have a higher peak stress then ESQ w/o RAP (p = 0.28). The interaction between resin type and RAP was not significant when evaluating the flexural modulus (p = 0.21). Formulations with RAP had a significantly higher flexural modulus then w/o RAP (p = 0.0001). Experimental resins with RAP had significantly higher maximum stress rates than those w/o RAP when evaluating polymerization stress (p = 0.0001). Finally, groups w/ RAP appeared to have a higher degree of conversion than groups without (p = 0.0057). This study showed that the experimental composites with RAP had greater mechanical properties than those without. Unfortunately, the increase in polymerization stress causes concern clinically due to the chance of leakage at the restoration/tooth interface. One of the main potential disadvantages of this new RAP technology is an increase in the polymerization stress. Deciding if this amount of polymerization stress is clinically acceptable is yet to be accomplished.
  • Thumbnail Image
    Item
    The influence of delayed light curing on the polymerization contraction stress and degree of conversion in dual-cured resin luting agents
    (2010) Iskandar, Mounir; Platt, Jeffrey A., 1958-; Andres, Carl J., 1942; Hovijitra, Suteena, 1944-; Brown, David T.; Levon, John A.
    The purpose of this study was 1) To determine the impact of eliminating or delaying the photo-activation procedure on the polymerization contraction stress (PCS)and degree of conversion (DC) of a dual-cured resin luting agent, and 2) To determine the amount of delay in photo-initiation of the dual-cured resin cements that can achieve a reduced PCS value with the highest possible DC. The amount of PCS and DC of a dual-cured resin luting agent was determined using a tensometer and ATR spectroscopic technique, respectively. Photo-activation delay in seven tested groups was 0 min, 2 min, 4 min, 6 min, 8 min, 10 min and no photoactivation. Five samples for each group were tested. There were two hypotheses for this study: 1) A significant decrease in the amount of PCS associated with delayed photo-activation, and 2) A significant increase in DC associated with delayed photo-activation.The PCS of the chemical-cure luting agent had significantly lower value than all of the light-cure groups. For the light-cure groups, those with a 4-min delay had higher PCS than those with delays of 0 min, 2 min, 6 min, 8 min, and 10 min. The zero (0)-min and 2-min delay had higher PCS than the 6-min, 8-min, and 10-min delay; and the 6-min delay had higher PCS than the 8-min and 10-min delay. The PCS decreased 0.086 MPa per minute of delay. The DC of the chemical-cure luting agent had significantly lower value than the 2-min, 4-min, 6-min, 8-min, and 10-min delaylight cure. For the light-cure groups, 0-min delay had a lower DC than the 2-min, 4-min, 6-min, 8-min, and 10-min delay; 2-min delay had lower DC than 4-min, 6-min, 8-min, and 10-min delay. The 4-min and 6-min delay had lower DC than the 8-min and 10-min delay; and the 8-min delay had a lower degree of conversion by peak area than the 10- minute delay. The DC increased 0.021 per minute of delay. Extending the stress relief period of the dual-cured luting agents by delaying light activation has a significant impact on PCS and DC values. There was significant decrease in PCS with the delayed light curing of the resin luting agent. Significant increase in DC was noticed when light activation was delayed in the dual-cured resin luting agents.
  • Thumbnail Image
    Item
    Mechanical properties evaluation of denture base PMMA enhanced with single- walled carbon nanotubes
    (2010) Scotti, Kevin; Chu, Tien-Min Gabriel; Paez de Mendoza, Carmen Y.; Andres, Carl J., 1942-; Levon, John A.; Hovijitra, Suteena, 1944-
    Recent theoretical and experimental studies, suggest that Carbon nanotubes are 10-100 times higher than the strongest steel at a fraction of the weight. There are two main types of CNTs that can have high structural perfection. Single-walled nanotubes (SWNTs) consist of a single graphite sheet seamlessly wrapped into a cylindrical tube. Multi-walled carbon nanotubes (MWNTs) comprise an array of such nanotubes concentrically nested like rings of a tree trunk. Denture base acrylics have been reinforced with different materials with limited success. No single reinforced material has showed a great statistical difference in mechanical improvement. The goal of this investigation was to study the effects of Single Walled Carbon Nanotubes reinforcement on the mechanical properties of commercially available denture base PMMA. Denture Base material was reinforced with Single-walled Carbon Nanotubes (SWNTs) at dispersion of 0.25 wt % (group 1), 0.50 wt % (group 2), 0.75 wt % (group 3) and 0.0 wt % (group 4, control). Samples from each group were evaluated for microhardness, flexural strength, flexural modulus, and fracture toughness. The samples were tested in two conditions, as manufactured (dry) and after storing at 37 C for 7 days (wet). Data from four experiments was analyzed by ANOVA. All control sample values were in the range of acceptance compared with previous studies. Higher values were obtained for the control groups for flexural strength and modulus compared with the experimental samples. (p < 0.05) There was no statistical difference regarding fracture toughness between control and experimental groups. A statistical difference was observed in Hardness. The experimental group showed higher values under compression.